- 您现在的位置：买卖IC网 > Sheet目录1253 > XR16M890IL32-0C-EB (Exar Corporation)BOARD EVAL XR16M890IL32
XR16M890
UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
REV. 1.0.0
3.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
enable the wake up interrupt. They are defined as follows:
FCR[0]: TX and RX FIFO Enable
? Logic 0 = Disable the transmit and receive FIFO (default).
? Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
? Logic 0 = No receive FIFO reset (default)
? Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
? Logic 0 = No transmit FIFO reset (default).
? Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: Enable wake up interrupt (requires EFR bit-4 = 1)
? Logic 0 = Disable the wake up interrupt (default).
? Logic 1 = Enable the wake up interrupt.
FCR[5:4]: Transmit FIFO Trigger Select (requires EFR bit-4 = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 10 below shows the selections. Note that the
receiver and the transmitter cannot use different trigger tables. Whichever selection is made last applies to
both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 10 shows the complete selections.
Note that the receiver and the transmitter cannot use different trigger tables. Whichever selection is made last
applies to both the RX and TX side.
34
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
XR18W750/753-0B-EB
EVAL BOARD FOR XR18W750/753
XRP2526EVB
BOARD EVAL POWER SWITCH XRP2526
XRP2528EVB
BOARD EVAL POWER SWITCH XRP2528
XT800SM
GAS TRIGGER TUBE 800V SMD
YMCRPR8C25
REF PLATFORM MOTOR CTRL R8C/25
ZB3251
INLINE FUSE HOLDER PLASTIC BODY
ZB3260
INLINE FUSE HOLDER BAKELITE BODY
ZB3270
PANEL MOUNT FUSE HOLDER
相关代理商/技术参数
XR16M890IL32-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 4GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL32TR
制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL32TR-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 4GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL40
制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL40-0C-EB
功能描述:UART 接口集成电路 EVAL F/M890 QFN40 MOT, INTEL, VLIO INT RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL40-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 8GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL40TR
制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL40TR-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 8GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel